XP600 CAPPINGS

XP600 Capping Station

Protect your XP600 printhead and maintain consistent print quality with the XP600 Capping Station—also called a cap top, capping unit or ink stack. It seals the printhead when the printer is idle, helping prevent ink from drying out, reducing the risk of nozzle clogs and supporting reliable cleaning cycles.

This is an essential maintenance component for compatible XP600-based DTF, UV DTF and eco-solvent printers. A worn, cracked or poorly sealing capping station can affect cleaning performance, cause air to enter the ink system and contribute to nozzle blockages.dtf+2

What the capping station does

When the printer is not printing, the carriage parks the printhead over the capping station. The rubber cap creates a seal around the nozzle plate, helping limit ink evaporation and protect the nozzles from dust and drying.manuals+1

During a cleaning or priming cycle, the capping station also helps create suction so the waste pump can draw ink through the nozzles. This helps clear air bubbles, minor blockages and dried ink from the printhead. A good seal is essential; if the cap does not seal properly, a cleaning cycle may pull air instead of ink.manuals+1

Key functions

The XP600 capping station supports:

• Sealing the printhead when the printer is idle.

• Helping prevent ink drying and nozzle clogging.

• Supporting cleaning and priming cycles through suction.

• Directing waste ink to the waste-ink system.

• Helping maintain consistent ink flow and print quality.

• Protecting the printhead during periods of non-use.

It works together with the printer’s waste pump, ink tubes, dampers and wiper assembly. If one of these components is faulty, replacing only the capping station may not fully resolve a printing problem.manuals+1

Suitable printers and systems

The XP600 capping station is used in compatible printers built around XP600 or XP600-series printheads, including many DTF, UV DTF and eco-solvent machines. Some listings specify compatibility with dual-pipe XP600 systems, while others describe compatibility with ink tubes of a particular inner diameter.dtfshop+1

Before ordering, confirm that the capping station matches your printer’s printhead arrangement, tube diameter, pump connection and carriage layout. A single-head and double-head printer may require different capping configurations.manuals+1

Maintenance tips

Keep the capping station clean to maintain a proper seal. Inspect the rubber caps for dried ink, swelling, cracks or debris, and clean them gently using a lint-free cloth and a printer-approved cleaning solution or distilled water. Avoid harsh chemicals and allow the parts to dry fully before restarting the printer.manuals+2

For DTF printers using white ink, regular maintenance is especially important because white pigment can settle and build up around the cap, tubes and pump. Some suppliers recommend replacing the capping station periodically—commonly every six to eight months depending on usage—though the correct interval depends on your printer, ink and production volume.dtf+1

Signs it may need replacement

Consider inspecting or replacing the capping station if you notice:

• Nozzle checks that do not improve after cleaning cycles.

• Cleaning cycles that pull air instead of ink.

• White ink draining back from the lines.

• Dried ink build-up around the cap tops.

• Cracked, swollen, hardened or warped rubber caps.

• Poor sealing when the printhead parks.

• Frequent clogging or inconsistent print output.

A weak cap seal can prevent effective cleaning and may allow air into the ink system. Check the cap alignment, rubber condition, waste tubes and pump performance before assuming the printhead is faulty.manuals+1

Confirm these details before ordering

Capping stations vary by printer brand and configuration. Ask the seller to confirm:

• Compatibility with your exact printer model and XP600 head version.

• Whether it is for a single-head or double-head printer.

• The ink-tube inlet diameter and pump connection type.

• Whether the capping station includes the cap top, pump, wiper or mounting bracket.

• Whether it suits DTF, UV DTF or eco-solvent ink systems.

• The recommended replacement interval and availability in Kenya.

Product summary

The XP600 Capping Station is a replacement maintenance part that helps seal the printhead, support cleaning cycles and reduce the risk of nozzle drying or clogging. It is a useful spare part for XP600-based DTF, UV DTF and eco-solvent printers. Confirm compatibility with your printer’s head arrangement, tube size and pump system before ordering.